manualshive.com logo in svg

Harman Accentra, Installation & Operating Manual, Page: 40 / 48

Share
Download
Harman Accentra Installation & Operating Manual Download Page 40

3-90-00674R20_08/12

Service Parts

07/12

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement 

parts for your appliance please provide model number and serial number. All parts listed 

in this manual may be ordered from an authorized dealer.

Stocked

at depot

ITEm

description

COmmENTS

PArT NumbEr

16

Finished Body Weldment

1-89-674001W

17

Cast Center Medallion

3-00-674060

Y

18

Cast Heat Exchanger CVR

Qty. 2 Req.

3-00-674050

Y

19

Flame Guide 

3-00-03000

Y

20

Hopper Lid Latch Kit

Sold as kit only

1-00-674139

Y

21

Cast Wing Center

4-00-674058P

Y

22

Cast Hopper Lid

1-10-674059

Gasket, Hopper Top

1-00-375501

Y

23

Hopper Lid Hinge Retainer

Pkg of 4

1-00-674083

24

Cast Top

4-00-674055A

25

Cast Wing Left

4-00-674056P

Y

26

Door Assembly

4-00-674053A

Y

Door Latch

3-00-249119

Y

Glass

3-40-674090

Y

Glass Clip

Pkg of 4

1-00-249140

Y

Rope 3/16” Gasket w/PSA (Glass)

10 Ft

1-00-1186258229

Y

Rope 3/8” Gasket 

(Door)

30 Ft

1-00-00888

Y

Wood Handle & Bolt

Pkg of 2

1-00-00247

Y

27

Cast Bottom Ashlip

3-00-674051P

28

Cast Side Panel

Qty 2 Req.

4-00-674054P

29

Cast Wing Right

4-00-674057P

Y

30

Burn Pot Weldment

1-10-00675

Y

Igniter Element

3-20-677200

Y

Pkg of 10

1-00-67200

Y

Igniter Cradle, Holder, Flat bottom

3 Sets

1-00-06620

Y

Ceramic Insert Gasket

3-44-724114

Y

Cleanout Cover

2 sets

1-00-06623

Y

Thumb Screw

Pkg of 10

3-31-782108-10

Y

31

Ash Pan  

1-10-674030

Y

32

Fan Protector Angle 

Qty 2 Req.

2-00-06114B

33

Distribution Blower

3-21-47120

Y

34

Hinge Plate

Qty 2 Req.

3-00-674047

35

Flue Box Cleanout Cover

2-00-674009B

36

Burn Pot /Tail Pipe Gasket

Pkg of 5

1-00-07381

Y

37

Feeder Assembly

Pre 008240096

1-10-01679A

38

Post 008240096

1-10-01779A

Additional service parts on following page.

Accentra (Insert)

beginning manufacturing date: N/A 

Ending manufacturing date: Active

Summary of Contents for Accentra

















































Reviews:

No comments