manualshive.com logo in svg

Harman Accentra, Installation & Operating Manual, Page: 1 / 48

Share
Download
Harman Accentra Installation & Operating Manual Download Page 1

3-90-00674R20_08/12

SAFETY NOTICE

PlEASE rEAd ThIS ENTIrE mANuAl bEFOrE YOu INSTAll ANd uSE YOur NEw rOOm hEATEr.  FAIlurE 

TO FOllOw INSTruCTIONS mAY rESulT IN PrOPErTY dAmAgE, bOdIlY INjurY, Or EvEN dEATh.

FOr uSE IN ThE u.S. ANd CANAdA.  SuITAblE FOr INSTAllATION IN mObIlE hOmES

IF ThIS APPlIANCE IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT.  FOr YOur SAFETY, FOllOw 

INSTAllATION dIrECTIONS. dO NOT uSE mAkEShIFT COmPrOmISES. 

CONTACT lOCAl buIldINg Or FIrE OFFICIAlS AbOuT rESTrICTIONS ANd INSTAllATION INSPECTION 

rEQuIrEmENTS IN YOur ArEA.

CONTACT YOur lOCAl AuThOrITY (SuCh AS muNICIPAl buIldINg dEPArTmENT, FIrE dEPArTmENT, FIrE 

PrEvENTION burEAu, ETC.) TO dETErmINE ThE NEEd FOr A PErmIT.

CETTE guIdE d'uTIlISATION EST dISPONIblE EN FrANCAIS. ChEz vOTrE CONCESSIONNAIrE dE hArmAN.

SAvE ThESE INSTruCTIONS.

The harman Accentra Pellet Insert

Installation & Operating manual

“Ce manuel est disponible en Français sur demande”

This  Fireplace  insert  may  be  installed  into  a  masonry  fireplace,  an  approved  manufactured  wood  burning 

fireplace (see page 25), Or, It may be built in to a wall or mantle system when using the optional zero clearance 

cabinet (see page 26).

Summary of Contents for Accentra

















































Reviews:

No comments