background image

 
 

 

HS / HL Valves & Systems Service Manual 

 

Hankscraft Runxin, LLC        300 Wengel Drive        608.524.9465        hrh2o.com        [email protected] 

52 

 
 

Be sure to shut off any bypass line. 
 
 

16.

 

Check for leaks at all seal areas. 
 

17.

 

Plug electrical cord into outlet. 
 

18.

 

Set time of day. 
 

19.

 

Return the control valve to the In Service position. 
 

20.

 

Replace the control valve back cover. Be sure grommet at cable hole is in place. 
 

Make sure there is enough brine in the brine tank. 
 

21.

 

Rotate program wheel counterclockwise until it stops at Regeneration position. 
 

22.

 

Start regeneration cycle manually if water is hard. 
 

23.

 

Plug cable into meter cover. Rotate cable to align drive flat if necessary. 
 

 
Replacing Meter Cover and Impeller 

 

1.

 

Unplug electrical cord from outlet. 
 

2.

 

Turn off water supply to system. 
 

3.

 

Relieve water pressure in the system by putting the valve in the Backwash position momentarily. 
 

4.

 

Return the valve to the In Service position. 
 

5.

 

Pull cable out of meter cover. 
 

6.

 

Remove four screws on cover. 
 

7.

 

Lift cover off of meter module, discard O-ring. 
 
 

Summary of Contents for HS Series



























































Reviews: