H&S GM 170 Operator'S Manual And Parts List Download Page 10

Page: 10 / 86

RECOGNIZE SAFETY INFORMATION

This is the safety-alert symbol. When you see this symbol
on your machine or in this manual, be alert to the potential
for personal injury.

Follow recommended precautions and safe operating
practices.

UNDERSTAND SIGNAL WORDS

A signal word- DANGER, WARNING, or CAUTION - is
used with the safety-alert symbol. DANGER identifies the
most serious hazards.

Safety signs with signal word DANGER or WARNING are
typically near specific hazards.

General precautions are listed on CAUTION safety signs.

FOLLOW SAFETY INSTRUCTIONS

Carefully read all safety messages in this manual,
and all safety signs on your machine. Follow all
recommended precautions and safe operating
procedures.

Keep signs in good condition. Immediately replace
any missing or damaged signs.

-8-

SAFETY INFORMATION

Summary of Contents for GM 170























































































Search results

Summary of Contents for GM 170

Reviews:

Related manuals for GM 170

Brands by name

Popular brands

H&S GM 170, Operator'S Manual And Parts List

Search results

Summary of Contents for GM 170

Reviews:

Related manuals for GM 170

Brands by name

Popular brands