H&S GM 170 Operator'S Manual And Parts List Download Page 41 | Manualshive

Page: 41 / 86

background image

OPTIONAL FEATURES & ACCESSORIES

ELECTRONIC SCALES & COMPONENTS

-39-

Model: Digi-Star EZ 2000

An optional factory installed Digi-Star EZ 2000 scale is available for accurate
weight measurement. The 3-point Weighbar System features 3 modes, Net,Tare
and Gross.

SWINGING INTAKE AUGER (SIA)

An optional Swinging Intake Auger(SIA) with a variable speed control
is available for the GM 170.

FENDER SET

A fender set is available and consists of 2 fenders, 4 fender support angles
and attaching hardware. Installation instructions are packaged with the kit of
parts.

Model: Digi-Star EZ 3200 w/External Horn

An optional factory installed Digi-Star EZ 3200 scale is available

with all the

features of the EZ 2000, plus an external horn, and has the capability for entering
rations.

SCREENS

12 sizes of screens are available. Sizes include:

1/8”, 3/16”, 1/4”, 5/16”, 3/8”, 1/2”, 5/8”, 3/4”, 1”, 1-1/4”, 1-1/2’, & 2”.

TRANSPORT LIGHTING

An optional highway transport lighting kit is available.

«
...
39
40
41
42
43
...
»

Summary of Contents for GM 170























































































Reviews:

No comments

Related manuals for GM 170

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

Infield Rascal Pro

Brand: ABI Attachments Pages: 8

Brand: Abicor Binzel Pages: 84

Brand: ABI Attachments Pages: 5

Brand: abem Pages: 47

Brand: Abely Pages: 5

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Backyard Play Systems Pages: 52

Brand: Backyard Play Systems Pages: 19

Brand: Backyard Play Systems Pages: 44

Brand: Bacharach Pages: 2

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Brand: Garelick Pages: 4

Brand: Rational Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands