Handicare TROPHY 20 Page 55 Service Manual Download

Page: 55 / 99

Service instructions | 55

Trophy 20

Service instructions | 55

Replacing the shock absorber - rear

Preparation

• Switch off the scooter with the ignition key.

Instructions

The following operations are required to replace the shock
absorber - rear:

Note!

Suitable work area required!

• Remove the seat.
• Lift the scooter to raise the wheels clear from the

ground.

•  Remove the rear cover.
•  Remove the battery cover.
•  Remove the roll-bar
•  Remove the hexagon head cap screw
•  Take out the shock absorber.
•  Read the table for more information about the

adjustment of shock absorbers.

• Use the special adjustment tool to adjust the shock

absorber as desired.

• Mount the new, correct adjusted, shock absorber.
• Rebuild the scooter in the reverse order.

Relevant article numbers

• 9000603 Shock absorber standard
• 9000683 Shock absorber heavy duty

Tools used

•  Socket, 7 mm / 17 mm
•  Allen key, 8 mm
•  9000825 Suspension adjustment key

Notice

• Make sure the scooter is switched off.

Summary of Contents for TROPHY 20




































































































Search results

Summary of Contents for TROPHY 20

Reviews:

Related manuals for TROPHY 20

Brands by name

Popular brands

Handicare TROPHY 20, Service Manual

Search results

Summary of Contents for TROPHY 20

Reviews:

Related manuals for TROPHY 20

Brands by name

Popular brands