Handicare TROPHY 20 Page 74 Service Manual Download

Page: 74 / 99

Trophy 20

74 | Service instructions

Mount the crutch holder, chassis

Preparation

• Switch off the scooter with the ignition key.

Instructions

The following operations are required to mount the crutch
holder on the chassis:

Note!

Suitable work area required!

• Remove the rear cover.
• Remove the two hexagon bolts and washers to remove

the rear bumper.

• Mount the crutch holder bracket on the rear frame side

of the electronics compartment.

• Drill two holes in the rear bumper (drill location is

indicated on the inside).

• Replace the rear bumper and mount the crutch holder

via the bumper on the bracket.

Relevant article numbers

• 1012515 Crutch holder mounted to chassis

Tools used

• Torque wrench, socket, 7 mm
• Metal drill, 4 mm
• Drill

110948-03-013

110948-03-014

110948-03-015

110948-03-015A

Ø4

Summary of Contents for TROPHY 20




































































































Search results

Summary of Contents for TROPHY 20

Reviews:

Related manuals for TROPHY 20

Brands by name

Popular brands

Handicare TROPHY 20, Service Manual

Search results

Summary of Contents for TROPHY 20

Reviews:

Related manuals for TROPHY 20

Brands by name

Popular brands