Handicare TROPHY 20 Page 43 Service Manual Download

Page: 43 / 99

Service instructions | 43

Trophy 20

Service instructions | 43

Replacing the mechanical brake

Preparation

• Switch off the scooter with the ignition key.
• Use a lifting device to raise the scooter clear of the

ground.

Instructions

The following operations are required to replace the
mechanical brake:

Note!

Suitable work area required!

• Remove the cap and hexagon

ange bolt to remove the

rear wheel.

• Remove the brake cable.
• Remove the two hexagon head cap screw and remove

the brake.

•  Mount the new brake.
•  Rebuild the scooter in the reverse order.
•  Use Loctite 243 before fastening the hexagon

ange bolt

with 90 Nm.

Relevant article numbers

• 9004141 Brake left

Tools used

• Screwdriver
• Torque wrench, socket, 16 mm
• Allen key, 4 mm
• Loctite

243

Notice

• N.a.

Note! Use Loctite 243 at the indicated locations during
assembling the wheelchair.

Summary of Contents for TROPHY 20




































































































Search results

Summary of Contents for TROPHY 20

Reviews:

Related manuals for TROPHY 20

Brands by name

Popular brands

Handicare TROPHY 20, Service Manual

Search results

Summary of Contents for TROPHY 20

Reviews:

Related manuals for TROPHY 20

Brands by name

Popular brands