Handicare Ibis 24 User Manual Download

Page: 47 / 52

Technical specification

XXXXXX-010900000-en.doc

7.1

Product specifications

Manufacturer: Handicare

XXXXXX-010901000-en.doc

7.1.1

Ibis 12"

Model Ibis

12"

Maximum user's weight

125 kg (8.7")

Description

Min.

Max.

Total length including leg-rest

920 mm (8.7")

1.200 mm (8.7")

Total width

630 mm (8.7") 720

(8.7")

Transport length

750 mm (8.7")

Transport width

610 mm (8.7")

Transport height

620 mm (8.7")

Total weight

35 kg (8.7")

Transport weight heaviest part

28 kg (8.7")

Static stability downward

10°

Static stability upward

11°

Static stability sideways

15°

Tilt adjustment mechanical

3°

28°

Seat angle

1°

6°

Effective sitting depth (adjustable)

440 mm (8.7")

520 mm (8.7")

Effective sitting width (adjustable)

380 mm (8.7")

525 mm (8.7")

Sitting height from the front

500 mm (8.7")

600 mm (8.7")

Back angle

83°

120°

Back height

520 mm (8.7")

570 mm (8.7")

Lower leg length

390 mm (8.7")

500 mm (8.7")

Leg-rest angle

32°

105°

Arm-rest height

170 mm (8.7")

240 mm (8.7")

Front arm-rest to backrest

370 mm (8.7")

450 mm (8.7")

Minimum radius

1.540 mm (8.7")

Ground clearance

40 mm (8.7")

Height of push bracket (adjustable)

980 mm (8.7")

1.200 mm (8.7")

Test data
Weight test dummy

125 kg (8.7")

Summary of Contents for Ibis 24





















































Search results

Summary of Contents for Ibis 24

Reviews:

Related manuals for Ibis 24

Brands by name

Popular brands

Handicare Ibis 24, User Manual

Search results

Summary of Contents for Ibis 24

Reviews:

Related manuals for Ibis 24

Brands by name

Popular brands