Handicare Ibis 24 User Manual Download | Manualshive

Page: 33 / 52

background image

Adjustment options

33

Set the side panels equally, in such a way that you feel comfortable
and that you have enough support and enough freedom of
movement.

•

Tighten the Allen bolts properly on both sides.

XXXXXX-010502030.nl.doc

5.2.4

Adjusting the seat angle

See fig. 010502040.

The seat angle of the seating system can be
adjusted continuously using the tilting
mechanism. See 'Tilting the seating system'.
The minimum seat angle of this tilting
mechanism can be adjusted for each user
individually. Using this adjustment, the
assistant can set the seating system in the
pre-set angle and use it as the basic position.

Before adjusting the minimum seat angle you
must leave the chair.

The minimum seat angle must be adjusted as follows:

•

Loosen both nuts (A) with a spanner with a key width of 13 mm.

•

Adjust the new angle by turning the bolts (B) in or out some more.
Turning them out will increase the seat angle.
Turning them in will decrease the seat angle.

•

Tighten the nuts in the position finger-tight.

•

Try the new position.

•

Lock the new seat angle by tightening both nuts securely.

SADKIB-010502040-en.doc

5.3

Adjusting the back-support
angle

See fig. 010503010.

For optimal seating comfort the angle (B) of
the backrest can be adjusted continuously.

The angle of the backrest can be adjusted as
follows:

•

Loosen the two Allen bolts (A) on the left
side of the back, under the seat, two turns
with an Allen key with a key width of 5 mm.

•

Adjust the desired back angle (B).

•

Tighten the Allen bolts again.

SADKIB-010503010.nl.doc

A

A

B

010502040

B

A

010503010

«
...
31
32
33
34
35
...
»

Summary of Contents for Ibis 24





















































Reviews:

No comments

Related manuals for Ibis 24

GUARDIAN G2-105RX1

Brand: Medline Pages: 8

Brand: SOMA Pages: 32

Brand: Küschall Pages: 36

Brand: Quantum Pages: 2

Brand: decon Pages: 10

Brand: Z-Tec Pages: 4

Brand: PaceSaver Pages: 44

Eclips X4 kids 90 Degrees

Brand: Vermeiren Pages: 152

Brand: Sahara Pages: 20

Quickie Freestyle M11

Brand: Quickie Pages: 40

Brand: Sopur Pages: 128

UNAwheel Mini Active

Brand: UNAcare Pages: 180

Home Care DN7110

Brand: Moen Pages: 4

Brand: Breezy Pages: 44

Brand: Invacare Pages: 2

Storm Torque SP

Brand: Invacare Pages: 4

top end pro 2 all sport

Brand: Invacare Pages: 16

Brand: Invacare Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands