manualshive.com logo in svg

Handicare Ibis 24, User Manual

Share
Download
Handicare Ibis 24 User Manual Download Page 32

Adjustment options 

 

32 

Tighten the locking bolts on both sides securely. 

 
XXXXXX-010502020.nl.doc 

 

5.2.2

 

Position of seat cushion 

See fig. 010502050. 
 
The seat cushion can be fastened to the 
frame in three positions. This allows the seat 
depth to be reduced. 
 
The location of the seat cushion can be 
changed as follows: 

•

 

Remove the seat from the chair by pulling 
it up. 

•

 

Loosen the two clamps (B) with a Phillips 
screwdriver PH2. 

•

 

Place the clamps at one of the other 
places (A). 

•

 

Place the seat on the chair by clicking the 
clamps on the front round tube of the seat frame. 

 
 

Check whether the seat is clicked in place securely. 

 

 
XXXXXX-010502050.nl.doc 

 

5.2.3

 

Adjusting the seat width 

See fig. 010502030. 
 
The space between the two arm-rests can be 
adjusted as desired between  
36 cm and 52 cm (15" and 20").  
The holder for the arm-rests can be shifted in 
width on both sides 

 

Do the adjustment, or have it done by 
someone, and then take your seat in the 
chair. 

 

The seat width adjustment should be done as 
follows: 

•

 

Loosen the two Allen bolts (A) on both sides of the chair frame with an Allen key with 
a key width of 4 mm. 

•

 

Slide the arm-rests to the desired width. 

 

B

A

010502050

A

010502030

Summary of Contents for Ibis 24





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands