manualshive.com logo in svg

Handicare Ibis 24, User Manual

Share
Download
Handicare Ibis 24 User Manual Download Page 39

 

Adjustment options 

 

39 

•

 

Lock the Allen bolt with the locking nut. 

5.6.2

 

Adjusting the depth of the 
footplate 

See fig. 010506020. 
 
The depth of the footplate can be adjusted in 
two different positions.  
For this the left and right footplate should be 
exchanged. 
 
The exchanging of the footplates should be 
done as follows. 

•

 

Remove the calf strap.  
See 'Removing calf strap'. 

•

 

Loosen the set bolt (A) a few turns with an 
Allen key with a key width of 4 mm. 

•

 

Let the foot-rest (B) lower together with the profile (C) from the top tube (D). 

•

 

Exchange both footplates for each other and slide them into the top tubes. 

•

 

Adjust the footplates to the desired height. 

•

 

Tighten the setscrews. 

•

 

If necessary, readjust the angle of the footplate. See 'Adjusting the angle of the 
footplate'. 

 
XXXXXX-010506020.nl.doc 

 

5.7

 

Adjusting the armrest 

See fig. 010508000. 
 
The arm-rests provide support to the arms to 
limit the burden on the shoulders. For this 
purpose the arm-rests can be adjusted in 
terms of height (A) and depth (B). 
The arm-rests can also be removed (C), to 
make space to leave the wheelchair 
sideways, for example if you make a transfer 
from a car seat. 
By removing the arm-rests the wheelchair can 
be made smaller, which simplifies transport. 

 
SADKIB-010508000.nl.doc 

C

A

B

010508000

A

C

B

D

010506020

Summary of Contents for Ibis 24





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands