Handicare Ibis 24 User Manual Download

Page: 42 / 52

Adjustment options

5.9.1

Adjusting the height of the
headrest

See fig. 010510010.

The height adjustment can be done as
follows:

•

Loosen the wing nut (A) a few turns.

•

Slide the headrest (B) to the desired
height.

•

Securely tighten the wing nut again so that
the headrest cannot shift.

XXXXXX-010510010.nl.doc

5.9.2

Adjusting the depth of the
headrest

See fig. 010510020.

The depth adjustment should be done as
follows:

•

Loosen the two bolts (A) a bit with a
spanner with a key width of 10 mm.

•

Set the desired headrest depth (B).

•

Tighten the two bolts securely again.

XXXXXX-010510020.nl.doc

5.9.3

Adjusting the angle of the
headrest

See fig. 010510030.

The adjustment of the angle should be done
as follows:

•

Loosen the bolt (A) a bit with a spanner
with a key width of 10 mm.

•

Set the desired angle (B).

•

Tighten the bolt securely again.

XXXXXX-010510030.nl.doc

010510010

010510020

010510030

Summary of Contents for Ibis 24





















































Search results

Summary of Contents for Ibis 24

Reviews:

Related manuals for Ibis 24

Brands by name

Popular brands

Handicare Ibis 24, User Manual

Search results

Summary of Contents for Ibis 24

Reviews:

Related manuals for Ibis 24

Brands by name

Popular brands