Handicare Ibis 24 User Manual Download

Page: 43 / 52

Adjustment options

5.10

Adjusting the calf strap

See fig. 010511000.

The calf strap (A) serves to support the calves
and is attached to the leg-rests. The calf strap
can be removed to make transfer in and out
easier.

EBAPUM-010511000.nl.doc

5.11

Adjusting the calf pad (option)

See fig. 010512000.

The calf pad serves to support the calf and is
placed on a leg support.
The calf pad can be adjusted in:
A

Height

Angle

XXXXXX-010512000.nl.doc

5.11.1

Adjusting the height of the
calf pad

See fig. 010512010.

The calf pad can be adjusted in height as
follows:

•

Loosen Allen screw (A) a few turns with an
Allen key with a key width of
4 mm.

•

Slide the calf pad up to the desired height.

•

Tighten the Allen screw again.

XXXXXX-010512010.nl.doc

010512000

010512010

010511000

Summary of Contents for Ibis 24





















































Search results

Summary of Contents for Ibis 24

Reviews:

Related manuals for Ibis 24

Brands by name

Popular brands

Handicare Ibis 24, User Manual

Search results

Summary of Contents for Ibis 24

Reviews:

Related manuals for Ibis 24

Brands by name

Popular brands