Halma Ocean Optics JAZ Installation And Operation Manual Download Page 20 | Manualshive

Page: 20 / 70

background image

2: Installing Jaz

10

013-RD000-000-02-201510

Installing the Jaz Unit

This section contains instructions for connecting Jaz directly to a computer through the USB port or to the
network through the Ethernet port.

Connecting Jaz to a Computer via USB

►

Procedure

1. Connect the USB (B) cable that you received with your Jaz unit from the JAZ-DPU module to

your computer.

2. When first connecting Jaz to your computer, you must run the Hardware Wizard for your PC to

recognize the new hardware. For Mac users, this step is not necessary.

3. In OceanView, use the Device Manager for your Jaz unit to be recognized in the OceanView

software.

Ethernet Connection

You can connect Jaz to the network via the Ethernet port on the JAZ-E module. A ferrite is provided with
your JAZ-E Ethernet module to be used in the event that you experience interference with any electronic
devices.

►

Procedure

Follow the steps below to connect the port on the Jaz Ethernet & Memory module to a Power Over
Ethernet (POE) bridge or a switch to the network (e.g., an 8-port network hub):

1. Find the Ethernet cable and the ferrite that you received in your Jaz package.

«
...
18
19
20
21
22
...
»

Summary of Contents for Ocean Optics JAZ







































































Reviews:

No comments

Related manuals for Ocean Optics JAZ

Brand: Makita Pages: 2

Brand: Makita Pages: 16

Brand: Eagle Eye Pages: 3

Brand: VALTRONICS Pages: 13

Brand: JIANGSU Pages: 8

Brand: Campbell Pages: 22

Brand: Campbell Pages: 32

Brand: Campbell Pages: 40

CR3000 Micrologger

Brand: Campbell Pages: 12

Brand: R.M. Young Pages: 8

Brand: Campbell Pages: 21

Brand: Kawai Pages: 66

HYDROMETTE BL Compact TF-IR 2

Brand: GANN Pages: 40

Brand: Gamry Pages: 16

Brand: OHAUS Pages: 2

Brand: velocomp Pages: 4

Brand: Lake Shore Cryotronics Pages: 97

Brand: Hanna Instruments Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands