Halma Ocean Optics JAZ Installation And Operation Manual Download Page 19 | Manualshive

Page: 19 / 70

background image

013-RD000-000-02-201510

9

Chapter 2

Installing Jaz

Overview

Your Jaz unit is field-portable and can collect data as a free-standing unit from the battery embedded in
the stack. You also have two options for connecting Jaz to a computer to process the data you have
collected:



A USB connection directly to a computer running OceanView.



An Ethernet connection to a computer network.

Note

Your Jaz unit receives power from either connection.

If you have purchased OceanView software, you must install it prior to connecting Jaz Spectrometer to a
computer. The OceanView software installation installs the drivers required for Jaz. If you do not install
OceanView first, the computer will not properly recognize Jaz. Follow the prompts in the OceanView
installer wizard.

If you have already connected Jaz to a computer running on a Windows platform prior to installing
OceanView, consult

Jaz Connected to Computer Prior to OceanView Installation

for information on

correcting a corrupt Jaz installation.

Caution

Connect all cables before powering-on your Jaz unit. Install Jaz in the following
order:

1.

Connect the external power supply (if used).

2.

Open OceanView.

3.

Connect the USB cable between Jaz and your computer (if used).

4.

Press F5 to display Jaz in OceanView.

«
...
17
18
19
20
21
...
»

Summary of Contents for Ocean Optics JAZ







































































Reviews:

No comments

Related manuals for Ocean Optics JAZ

Brand: Keithley Pages: 48

Brand: Abbott Pages: 296

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: Underground Magnetics Pages: 48

Brand: PCB Piezotronics Pages: 15

Vortex Flow Industry

Brand: Grundfos Pages: 16

Brand: Spacelabs Pages: 156

Brand: Trotec Pages: 14

Brand: GREISINGER Pages: 20

Brand: Kobold Pages: 19

Brand: AKCP Pages: 16

Brand: Swann Pages: 106

Brand: Hanna Instruments Pages: 2

Brand: Magnetrol Pages: 48

Brand: MetLogix Pages: 30

SensoControl ServiceJunior

Brand: Parker Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands