Smart Temp SMT-700 User Manual
Page 9 of 20
Tap the Clock button again, now the minute’s digits flashes. Using the up (
S
) or down (
T
) buttons set the minute to the time
you wish the “Start” event to commence.
Tap the Clock button again. If the SMT-700 thermostat has been set by the installer to control the optional climate zoning
AND if the option to program the zones has been set by the installer, you will now have the ability to set which zones you
require to be ON during the “Start” event. Using the up (
S
) or down (
T
) buttons set the zones you wish to be ON for the
“Start” event.
If the installer has set to the Program Zone option “OFF” this step is skipped by the SMT-700 thermostat during the
programming sequence.
Tap the Clock button again, now the word “Heat” (if heating mode is enabled by the installer) and a temperature value is
shown in the LCD, using the up (
S
) or down (
T
) buttons set the desired Heating temperature for the “Start” event. Tap the
Clock button again, now the word “Cool” (if cooling mode is enabled by the installer) and a temperature value is shown in the
LCD, using the up (
S
) or down (
T
) buttons set the desired Cooling temperature for the “Start” event.
NOTE: there must be a minimum of 1 deg C difference between heating and cooling set points. The heating temperature must
be at least 1 deg C lower than the cooling set temperature. If you set the heating or cooling set point closer than this minimum
value, the SMT-700 thermostat will automatically “push” the other set point away to maintain this minimum value.
Tap the Clock button again and the day previously selected will be shown along with the word “Stop”. The Hour digit will
flash indicating that this value can now be adjusted with the up (
S
) or down (
T
) buttons. Set the hour to the time you wish
the “STOP” event to commence.
Continue to tap the Clock button to advance you through the “Stop” “Minute”, then “Stop” Zone (if enabled) “Stop” Heating
(if enabled) and “Stop” cooling (if enabled) temperatures.
Taping the Clock button again the LCD will show the word “COPY”.
You now have TWO options
Option 1 - Continue Programming as above.
Simply continue to tap the Clock Button as you have been to advance to the next day, “Tuesday” in this example “Start” &
“Stop”, then Wednesday, Thursday etc, following the same simple steps previously explained…. OR
Option 2 - Copy Program – To copy the values you have just set to other days of the week.
Rather than taping the Clock button now, tap the up (
S
) or down (
T
) buttons to “TAG” each additional day you wish to copy
the currently set days program to. When you have finished “Tagging” the days you desire then press the Clock button to
initiate the copy process. The word “Copy” will flash briefly to confirm the copy process and your current days values will be
copied to the days selected. Normal programming will resume at the next day to be programmed.
(
Tip.
On days when the office will be unoccupied, it is a wise idea to set the “START” and “STOP” programs to occur at the same
time of day, say 8:00am for example. This way if “FAN ON” mode has been selected the fan will not start on those days where
the office is un-occupied.
After Hours Run Timer
Note - if zoning has been used in your office, the after hours run timer function is automatically disabled.
An extremely useful feature of your SMT-700 thermostat is it’s integrated after hours run timer function. This timer is useful
when you find yourself working outside of the normal office hours. Tapping the On/Off button will initiate the after hours
run timer function where the SMT-700 thermostat will then temporarily substitute that days “Stop” program temperatures with
that days “Start” program temperatures but only for a timed two hour period. While this after hours run timer is operating the
word “Timer” will flash on the LCD.
This function makes it extremely simple to return the office temperature to a comfortable working level without the fear of
forgetting to turn the air conditioning system off at the end of your day.
