Page 8 of 20
Mode
Tap this button to cycle the SMT-700 thermostat through the available modes, Heat only, Cool only, Fan Only (ventilation
mode) or Auto season change over mode. See page 12 of this manual for more information on Modes.
Up (
S
)
Use this button to increase the desired room temperature for the heating or cooling modes, or increase a “value” in
programming modes. Also used to force override the pre-programmed temperatures and temporarily replace them with a new
higher set temperature.
Down (
T
)
Use this button to decrease the desired room temperature for heating or cooling modes, or decrease a “value” in programming
modes. Also used to force override the pre-programmed temperatures and temporarily replace them with a new lower set
temperature.
Clock
Tap the clock button to begin setting the clock. Press and hold the clock button for 2 seconds to begin programming your daily
events.
Fan
Single Speed Fan -
. Tap this button to cycle between Continuous Fan (Fan ON) and Auto Fan.
Three Speed Fan
– Tap this button to cycle between Low, Medium, High & Auto Fan speeds.
Press and hold this button for 5 seconds to toggle between Continuous Fan (Fan ON) and Auto Fan.
Setting The Clock
Your SMT-700 thermostat is fitted with a real time clock. This clock is used by the SMT-700 thermostat for the programming
functions described below. It is essential that the clock time and day are set accurately if you require your programmed events
to start on time.
To set the clock, tap the clock button. The LCD will show the Hours Digit flashing. Use the up (
S
) or down (
T
) button to
adjust the hours to the correct time (note the AM / PM symbol) Tap the clock button again and now the minute’s digits will
flash. Adjust this value using the up (
S
) or down (
T
) button to show the correct minute. Tap the Clock button again and now
the week day flashes, again use up (
S
) or down (
T
) button to set this value to the correct day of the week. Tap the clock
button again to exit the clock set function.
Programming Your 2 Daily Events
The SMT-700 thermostat is an individual 7-day programmable thermostat. For each day of the week you are able to have 2
time schedules or programmed events occur. For clarity these events are conveniently named “Start” and “Stop”.
The “Start” event is used to set the time you wish your office to start at the beginning of the day. You can program your
desired heating and cooling temperatures that you wish your office to be when the start event begins.
The “Stop” event is used to set the temperatures you wish office to be at the end of the working day. You are able to program
your heating and or cooling to “OFF” or simply set a more economical temperature than your start program to prevent your
office over-heating or becoming to cool at during the night.
You are permitted to have the Start and Stop event occur at a different time of the day and set a different heating and cooling
desired set temperature for each of the 2 events. You are able to set a heating set point temperature between Heating OFF and
38 degrees Celsius. You are able to set a cooling temperature between zero degrees Celsius and Cooling OFF.
Programming your SMT-700 thermostat or setting these daily events is no more complicated than setting the clock as
described previously. The same buttons are used in the same sequence, using the Clock button to advance to the next step, and
the up (
S
) or down (
T
) buttons to make changes. The LCD shows only relevant information for the event being adjusted thus
reducing possible errors that may be caused by having confusing information displayed on the LCD.
This makes the programming of the SMT-700 thermostat a simple and logical process.
To enter the program mode, press and hold the Clock button for 5 seconds. The display will change and the Day “Monday”
will flash. Using the up (
S
) or down (
T
) buttons adjust the day to the day you wish to start programming or to the day you
wish to edit an existing program.
Tap the clock button to advance to the next step, The LCD will show the word “Start” with the hour’s digit flashing. Using the
up (
S
) or down (
T
) buttons to adjust the hours to the time you wish the “Start” event to commence for the day selected.
