hager TX216 Product Documentation Download Page 14 | Manualshive

Page: 14 / 130

hager TX216 Product Documentation Download Page 14

hager

Fitting, electrical connection and operation

Seite 14 von 130

Switching on the permanent manual control mode for broadcast

Permanent manual control mode for broadcast has been activated.

Press the key for at least 5 s

- or -

Switch off mains voltage supply.

Permanent manual control mode for broadcast has now been terminated. The status LED and the
7-segment display will extinguish.

•

When shutting off the temporary manual control mode for broadcast, the state selected by manual
control will not change.

Operating DALI devices in manual control mode for broadcast

The DALI Gateway has not yet been programmed via the ETS.

Manual control mode (permanent or temporary) has been activated.

Operate the devices by pressing the ON/ key or OFF/ key.
Brief press: Collective switch on/off.
Long press: Collective increase/decrease of brightness.
Long press & releasing: Stopping collective dimming.

All connected DALI devices will immediately execute the corresponding commands.

Switching off all DALI devices in manual control mode for broadcast

Permanent manual control mode for broadcast has been activated:

Press the ALL OFF key.

All connected DALI devices will be immediately switched off (brightness: 0 %). The devices are not
locked. Collective activation is again possible after shutoff.

•

The "ALL-OFF" function is not available in temporary manual control mode.

Activating temporary manual control mode

If the DALI Gateway has been programmed at least once via the ETS, at least one DALI group will be
created and configured. In this case, the created groups can be individually controlled via manual
control. The broadcast mode will be deactivated.

The DALI Gateway has been programmed at least once via the ETS.

Manual control has been enabled in the ETS.

Press the key briefly (< 1 s).

The group number “01” will be shown on the 7-segment display.

•

After 5 s without a key-press, the Gateway automatically returns to the bus mode.

•

The Gateway is delivered with the broadcast mode activated. After programming via the ETS, the
broadcast mode can be reactivated any time by unloading the application program via the ETS.

«
...
12
13
14
15
16
...
»

Summary of Contents for TX216



































































































































Reviews:

No comments