Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP Build Instructions Download

Page: 35 / 45

Check the fit of the first bracket

78-05

on the starboard

side of the funnel, beneath the searchlight platform

65-01

. When you are happy with the fit, glue in place.

The second searchlight bracket

78-05

is glued to the

port side of the funnel beneath the searchlight
platform

65-01

as shown.

Place the forward superstructure assembly on your
worktop. Take the funnel and thread its three cables
through the opening in superstructure deck

24-02

indicated by the red arrow.

Fit the funnel onto the forward superstructure so that
it butts up against the bridge deck

26-01

Holding the funnel assembly in place, carefully turn
the work so that you can access the underside of the
superstructure deck

24-02

. Use two

PWB

2 x 4mm

flange screws to fix the funnel in place, as shown.

Fit the foremast base

78-01

between the forward

superstructure (level with the admiral’s deck,

43-01

)

and the funnel, as shown. Glue the ends of the
foremast base in place.

65-01

78-05

43-01

78-01

78-05

65-01

24-02

26-01

24-02

PWB

. FINAL FUNNEL ASSEMBLY AND FOREMAST

AGORA

MODELS

AGORA

MODELS

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP














































Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands

Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP, Build Instructions

Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands