Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP Build Instructions Download

Page: 13 / 45

. FITTING THE MOTOR FOR THE FOURTH 15cm GUN

STAGE 73

GEAR ASSEMBLY FOR THE

SECOND 38cm GUN

73-01

73-09

2 x 6

2 x 4

73-02

73-03

73-04

73-05

73-06

73-07

73-08

73-11

73-10

72-01

73-01

70-04

72-01

73-01

COMPONENTS CHECKLIST
73-01:

Cog

73-02:

Motor housing

73-03

: Left support

bracket (L)

73-04:

Right support

bracket (R)

73-05:

Cog

73-06:

Cog

73-07:

Hub

73-08:

Gear arm

73-09

: Gear housing

73-10:

Gear housing

73-11:

Shaft

PB:

Six 2 x 6mm PB

screws

PB:

Seven 2 x 4mm PB

screws

Take the motor

72-01

from the previous issue. Fit the

cog

73-01

on to the shaft of the motor.

Take the deck assembly

19-01

22-01

48-01

and

position it upside down on your work surface, taking
care not to damage any fittings. Fit the motor

72-01

into the recess so that the teeth on the cog

73-01

engage with the teeth on the cog

70-04

(arrow).

AGORA

MODELS

AGORA

MODELS

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP














































Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands

Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP, Build Instructions

Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands