Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP Build Instructions Download

Page: 25 / 45

Repeat the previous step to assemble the starboard
crane, using the second boom

76-05

, trolley

and

hub

It is important to bend supports

and

the correct

way. Study this photograph and the next step very
carefully, noting the position of the tabs (arrows). Cut
the supports

and

from frame

76-10

. Take frame

(noting the positions of the tabs, see arrows) and

bend the sides up at right angles as shown.

Create a mirror image of support

by bending up

the sides of support

, as shown, noting the position

of the tabs.

Take the crane platform

76-03

and position it upside

down on your work surface. Identify the recesses for the
tabs on supports

and

, and glue them in place.

Fit the pins of the crane booms

76-05

into the upper

side of platform

76-03

. Note the positions of the

trolleys

and

Do not

glue in place.

Check the fit of the central tab on the platform

76-03

in the aft of the funnel. At the same time, the pins on
the top of the crane booms fit into holes in the
underside of the searchlight platform

63-05

76-03

63-05

76-03

76-05

76-03

76-05

AGORA

MODELS

AGORA

MODELS

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP














































Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands

Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP, Build Instructions

Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands