Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP Build Instructions Download

Page: 1 / 45

Pack 07 | Build Instructions

Your 1:200 scale model of the legendary battleship Bismarck is packed with

intricate details which precisely replicate every aspect of this state-of-the-

art warship. Each piece has been created using premium quality materials to

bring maximum enjoyment during your complete build.

In your seventh model pack, you will assemble:

North America Edition by Agora Models

STAGE 69: MOTOR FOR THE THIRD 15CM GUN

STAGE 70: THE FOURTH 15CM GUN TURRET

STAGE 71: THE NEXT KEEL SECTION

STAGE 72: MOTOR FOR THE FOURTH

15CM GUN

STAGE 73: GEAR ASSEMBLY FOR THE SECOND

38CM GUN

STAGE 74: ELEVATION MOTOR FOR THE

SECOND 38CM GUN TURRET

STAGE 75: DETAILS FOR THE UPPER DECK

STAGE 76: ROPE REELS AND FUNNEL DETAILS

STAGE 77: HULL SECTION AND FUNNEL

DETAILS

STAGE 78: FINAL DETAILS FOR THE FUNNEL

STAGE 79: THE NEXT HULL SECTION

STAGE 80: THE TWO AIRCRAFT HANGARS

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP














































Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands

Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP, Build Instructions

Search results

Summary of Contents for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Reviews:

Related manuals for AGORA BISMARCK THE LEGENDARY BATTLESHIP

Brands by name

Popular brands