Guardall G-DVR4 Page 6 User Manual Download

Page: 6 / 86

Chapter2 Installation

Warning: Before you install the DVR, please make sure that the power of DVR is
switched off.

2.1 Checking the DVR and Its Accessories

When you get the product, check that all the goods are included in your product

package. There is a list in the package. If any of the goods is missing, please contact
your dealer.

2.2 HDD Installation

Installation notice

There is no HDD in the DVR when leaving factory. According to the record

schedule, you can calculate the total capacity you need (refer to Appendix A). Please
ask the specialist to disassemble the DVR and install HDD.

Installation instrument

One cross screw driver

HDD installation

1.  Open the DVR box.
2.  Place the HDD on the mounting plate.
3.  Connect the ATA data cable correctly. First put the power plug of the HDD in

the motherboard. Plug the data line of the HDD into the SATA interface.

4. Fix the HDD into the Chassis.
5. Cover and fix the DVR box.

Note: After the HDD installation, you must format them. Please refer to

section 6.3

Summary of Contents for G-DVR4























































































Search results

Summary of Contents for G-DVR4

Reviews:

Related manuals for G-DVR4

Brands by name

Popular brands

Guardall G-DVR4, User Manual

Search results

Summary of Contents for G-DVR4

Reviews:

Related manuals for G-DVR4

Brands by name

Popular brands