Guardall G-DVR4 User Manual Download | Manualshive

Page: 50 / 86

background image

50

[EDIT] key to enable the flag into “

”.

Note: In order to make the cameras start recording, in “Recording” menu,

you must enable recording schedule and set “Rec Type” as “Motion Detection”
or “Motion | Alarm”. Please refer to chapter 5.12 for recording setup.

Step 7: Motion alarm schedule: When the motion alarm is happened in

schedule, DVR will response such as “On Screen Warning”, “Audible Warning”,
“Upload to Center” and “Trigger Alarm Output”. You can setup 4 time periods for one
day and 7 days for one week.

Note: Time periods in one day can not be repeated.

Step 8: Motion alarm handle method setup: You can select one or more handle

methods such as “On Screen Warning”, “Audible Warning”, “Upload to Center” and
“Trigger Alarm Output”.

Note: If “On Screen Warning” is enabled, when there is motion alarm

happened and DVR is in preview mode, DVR will switch to the related camera.
If you trigger more than one camera, DVR will pop-up them one by one every 10
seconds. When the motion alarm is disappeared, DVR will restore preview mode.

Step 9: Save motion alarm setup: Press “Confirm” button to return “Image

Setup” menu. In the “Image Setup” menu, press “Confirm” button to save the current
camera parameters.

Step 10: Save all cameras: You can repeat from step2 to step8 to setup motion

detection parameters for other cameras. Also you can copy the parameters of one
camera to any other cameras.

Note: Motion alarm area can not be copied.

If you want to disable motion alarm area and motion alarm policy, you just need

to select the motion alarm sensitivity as “Off”.

5.11 Preview

After the device started, the preview screen will be seen; then you can press

“PREV” key to switch between one screen and four screens; also you can switch to
the other single screen by pressing “EDIT”; or in “SHIFT” mode you can press
numeric keys to switch to the screen no. you want.

In “Preview” menu, you can setup preview mode, screen switch time, enable or

disable audio preview and preview layout.

Step 1: Enter “Preview” menu: In the main menu, move “Active Frame” to

“Display” icon and press [ENTER], then go to “Preview Setup” and press [ENTER],
you can enter “preview” menu. Shown as Fig.5.20 below

«
...
48
49
50
51
52
...
»

Summary of Contents for G-DVR4























































































Reviews:

No comments

Related manuals for G-DVR4

Brand: Watcher Pages: 14

Brand: Ebode Pages: 104

Brand: Q-See Pages: 2

Brand: Dedicated Micros Pages: 2

Brand: COMPRO Pages: 56

VANGUARD II 8x4H

Brand: EverFocus Pages: 8

TiVo TCD24 Series

Brand: DirecTV Pages: 7

Brand: Luxon Video Pages: 133

Brand: Luxon Video Pages: 164

Brand: Uraku Pages: 56

Brand: Ness Pages: 12

Brand: AVer Pages: 19

Brand: Idis Pages: 16

Brand: Plustek Pages: 57

Wisenet HRD-1642

Brand: Hanwha Techwin Pages: 10

Brand: IntelLink Pages: 327

Brand: SJA Pages: 23

Brand: Digital Watchdog Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands