Guardall G-DVR4 User Manual Download | Manualshive

Page: 5 / 86

background image

5

Support changeable OSD position, support LOGO.
Support both variable bit rate and frame rate.
Support dual-stream, and the sub stream can support CIF/QCIF resolution.

Storage:

One SATA interface and the HDD can support up to 2000GB memory.

HDD S.M.A.R.T. technology

Support FAT32 file system

Support multiple record modes: schedule record, motion detection record,

external alarm record, motion & alarm record, motion or alarm record, manual
record.

Support cycle and none cycle record mode.

Support USB flash disk, USB hard disk and USB CD-RW/DVD-RW to

backup.

Preview

&

Playback:

Support one composite video output and one spot video output

G-DVR4 can support one VGA output with 1204*768 resolution.
Support VGA and VOUT output, VGA has precedence over VOUT, and can

not output at the same time.

Support play forward, backward, pause, frame-by-frame, etc.
User-defined preview layout.
Support one playback channel.

Network:

Support TCP, UTP, Multicast, DHCP, etc

G-DVR4 supports RTP.

Support ADSL (PPPoE) dialup function.

Remote parameters setup

Remote download and playback the recorded files

Remote upgrade the DVR firmware

Remote PTZ control

Support IE for network control

Remote alarm DVR information acquisition

Others:

Support network voice talk.
Support WATER MARK
Support local and remote PTZ control.
Support multi-level user management.
Support local and remote log searching function.
Automatically recovery from exceptions enables high reliable.
Provide SDK and demo source code for application development.

«
...
3
4
5
6
7
...
»

Summary of Contents for G-DVR4























































































Reviews:

No comments

Related manuals for G-DVR4

Brand: ESP Pages: 21

WJ-ND300A/10000V

Brand: Panasonic Pages: 66

Brand: Idis Pages: 32

Brand: Q-See Pages: 10

Brand: Canyon Pages: 88

Brand: Armed Security Pages: 16

Brand: Q-See Pages: 5

Brand: Costar Pages: 83

Brand: COP-USA Pages: 111

Brand: AWA Pages: 17

Brand: Samsung Pages: 1

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands