background image

31

Step 3

With the gate in the desired open position PRESS & HOLD the “LEARN MAST LIMIT" button on the control board for 5 

seconds. 

Step 4

Press the transmitter button and allow the gate to return to the closed position. YOUR GATE’S OPEN POSITION LIMIT IS 
NOW PROGRAMMED.

TESTING YOUR OPEN LIMIT SETTING:

Press your entry transmitter and allow your gate to open. If the 
OPEN position is not correct or needs to be changed, you will 
need to CLEAR your OPEN LIMIT settings and follow steps 
one (1) to four (4) again.

CLEARING PROGRAMMED
OPEN LIMIT SETTING:

If you make a mistake and set the limit at the wrong position 
– press your transmitter to return the gate to the fully closed 
position, then press and hold the "LEARN MAST LIMIT" button 
for 5 seconds. This will clear the memory for the
open limit position. Follow steps one (1) to four (4) again.

Learn Master Limit

Button

1

  2

  3

  4

O

N

 

D

IP

STATUS

LEARN  RMT

LEARN

MAST  LIMIT 

LEARN

SLV    LIMIT 

S3

S4

S2

ART  OFF
G       OFF

         PULL

EN     DLY.

            OFF
            OFF

ON
ON
PUSH
SIMULT.
ON
ON

120 MIN

MAX

CLOSE  TIME 

STALL   FORCE

Setting the Open Position Limit

Step 1

Confirm that the power switch is in the ON position, and the gate is in the CLOSED POSITION.

Step 2

Activate your opener by pressing the entry transmitter button. Your gate should now be moving from the closed position 
toward the open position. Prepare to STOP gate by pressing the entry transmitter button again when the gate reaches the 
desired open position. This step may be repeated until desired open position is achieved. Once the desired OPEN position has 
been achieved, proceed to Step 3. 

Summary of Contents for 4000XL











































Reviews: