GTO 4000XL Hec1005a Download

Page: 3 / 42

Gate Operator Class Categories ------------------------------------------------------------inside cover
Units and Standards Conversion Chart ---------------------------------------------------inside cover

PLEASE READ THIS FIRST! --------------------------------------------------

page iii

Important Safety Instructions --------------------------------------------------

page 1

Disconnecting the Operator -----------------------------------------------------------page 1

Important Safety Instructions for the Consumer ------------------------------------page 2

Secondary Means of Protection Against Entrapment ------------------------------page 5

Required Safety Precautions for Gates -----------------------------------------------page 6

Warning Signs and Labels -------------------------------------------------------------page 7

Installation --------------------------------------------------------------------------

page 8

Parts List ---------------------------------------------------------------------------------page 8

Technical Specifications -------------------------------------------------------------page 10

Installation Overview ------------------------------------------------------------------page 11

Installing the Mounting Hardware

----------------------------------------------------page 12

Installing the Post Bracket Assembly -------------------------------------------page 12

Installing the Gate Bracket -------------------------------------------------------page 15

Mounting the Operator ------------------------------------------------------------page 16

Installation of the Closed Position Stop ---------------------------------------------page 16

Mounting the Control Box -------------------------------------------------------------page 17

Connecting the Operator Power Cable ----------------------------------------------page 18

Installing the Battery -------------------------------------------------------------------page 18

Powering the System --------------------------------------------------------------

page 19

Solar Chart -------------------------------------------------------------------------------page 19

Connecting the Transformer -----------------------------------------------------------page 19

Control Board Settings ----------------------------------------------------------

page 22

DIP Switches ----------------------------------------------------------------------------page 22

Setting the Closed Position ------------------------------------------------------------page 23

Obstruction Sensitivity -----------------------------------------------------------------page 24

Setting Your Personal Transmitter Code -------------------------------------

page 25

Installing the Receiver -----------------------------------------------------------

page 26

Connecting Accessories ----------------------------------------------------------

page 27

Input Connections ----------------------------------------------------------------------page 27

Wiring Accessories ---------------------------------------------------------------------page 28

Push to Open Installation --------------------------------------------------------

page 29

Setting Open Position Limit ----------------------------------------------------------page 31

Troubleshooting Guide ------------------------------------------------------------

page 32

Repair Service ---------------------------------------------------------------------

page 35

Column Installation Information ----------------------------------------------

page 36

Accessory Catalog ----------------------------------------------------------------

page 37

Table of Contents

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Summary of Contents for 4000XL











































Search results

Summary of Contents for 4000XL

Reviews:

Related manuals for 4000XL

Brands by name

Popular brands

GTO 4000XL, Hec1005a

Search results

Summary of Contents for 4000XL

Reviews:

Related manuals for 4000XL

Brands by name

Popular brands