GTCO CalComp QUIKRULER User Manual Download | Manualshive

Page: 38 / 45

background image

GTCO

Message

Meaning

**Bad Ref Point*

This message will appear
during a Relocate Menu
operation if an incorrect lower
left or lower right reference
point is entered. Make sure
that the entire menu is within
the digitizer's measuring
area. Repeat the Relocate
Menu operation if this
message appears.

*Menu Off Tablet

This message will appear
during a Relocate Menu
operation if the QuikRuler
menu is not positioned
entirely within the digitizer's
measuring area. Move the
menu and repeat the
Relocate Menu operation if
this message appears.

*Number Too Big*

The number on line 2 of the

display is too large for
QuikRuler. Try changing
units to reduce the number
size if this message appears.

If you receive any of these messages and the
above suggestions do not correct the problem,
see your dealer for service.

36

Messages

53-00039 C.p65

10/4/00, 11:55 AM

38

«
...
36
37
38
39
40
...
»

Summary of Contents for QUIKRULER














































Reviews:

No comments

Related manuals for QUIKRULER

Brand: Abbott Pages: 296

Brand: jablotron Pages: 2

Brand: R&S Pages: 733

Brand: R&S Pages: 369

Brand: Orange Electronic Pages: 21

Brand: Gas Data Pages: 99

Brand: Omega Pages: 31

Dusty Harp Pickup Series

Brand: Dusty Strings Pages: 5

Brand: Chroma Pages: 63

Ranger TDR VDV501-090

Brand: Klein Tools Pages: 44

Brand: PRONIVO Pages: 40

Brand: socomec Pages: 34

Brand: LEGRAND Pages: 5

Digital Piano CA750

Brand: Kawai Pages: 76

Brand: Magnescale Pages: 2

Brand: Datakom Pages: 27

Duomat Evolution DeLuxe

Brand: Dennerle Pages: 27

Brand: Seaward Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands