GTCO CalComp QUIKRULER User Manual Download | Manualshive

Page: 39 / 45

background image

QuikRuler

37

Radio and Television
Interference

Radio and Television Interference
in the United States

This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.

However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and the receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

Shielded interface cables must be used with this
product.

Radio/Television

53-00039 C.p65

10/4/00, 11:55 AM

39

«
...
37
38
39
40
41
...
»

Summary of Contents for QUIKRULER














































Reviews:

No comments

Related manuals for QUIKRULER

Brand: Kawai Pages: 2

Brand: Eaton Pages: 53

Brand: Oceanic Pages: 75

Network Card-MS

Brand: Eaton Pages: 26

Brand: Unico Pages: 10

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 110

Portatone PSR-5700

Brand: Yamaha Pages: 79

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 108

Brand: Kawai Pages: 64

Brand: Kawai Pages: 28

Brand: Kawai Pages: 28

Brand: Parkside Pages: 120

Brand: Gallagher Pages: 20

LAQUAtwin-Na-11

Brand: horiba Pages: 5

Brand: RaySafe Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands