background image

Smart SVC Relay Instruction Manual 

36 

 

Off Set Output 

If you want “Off Set” stage to give input when this feature is activated, you should make it 
‘on’. 

 

 

Figure 3.73 

Off Set Enter 

The value of “Off Set” stage can be entered in this screen. 

 

 

 

Figure 3.74 

Off Set Reactive 

“Off Set” stage value is entered 100 VAr for each phase.  

 

 

 

Figure 3.75 

Off Set Pin 

If you want to enable or disable generator input pin “Off set” stage, make the parameter ‘on’. 
If 220 V is reached to the generator pin, the “Off set” state that is activated gets active. When 
it reaches to 0, the activated 'off set' state is made passive. 

 

 

Figure 3.76 

Inductive Ratio Hysteresis 

The system shows tolerance up to the inductive hysteresis value with Inductive Ratio Hysteresis 
Menu  and  the  necessary  capacitor  is  not  done.  It  is  used  to  extend  the  life  of  the  board  in 
situations that do not have trouble in terms of punishment. The relay intervenes in the system 
to reach inductive limit. If the obtained ratio after intervention is in hysteresis limits, it does not 
intervene anymore.  

EXAMPLE:

 

In case of inductive limit is 5% inductive ratio is 5, if the values stay 5% and 10% 

after the intervention, the relay does not intervene anymore. 

 

 

Figure 3.77 

End Ratio Hysteresis 

 

 

 

 

Off Set Output  

On 

 

 

 

 

 

Off Set Enter  

->Yes No 

 

 

 

 

 

Off Set Reactive  

 

 

 

 

 

Off Set Pin  

Off 

 

 

 

 

 

Summary of Contents for SMART GES1













































Reviews: