Grundfos BoosterpaQ Hydro MPC, Installation And Operating Instructions Manual

Page: 17 / 58

17
Section Display and display number See page
10.4 Status 18
10.4.1 Current alarms (3.1) 18
10.4.2 System status (1.2) 18
10.4.3 Operating mode (1.2.1) 19
10.4.4 Setpoint (1.2.2) 19
10.4.5 Setpoint influence (1.2.3) 20
10.4.6 Measured values (1.2.4) 20
10.4.7 Pump status (1.3 to 1.8) 20
10.5 Operation 20
10.5.1 Operation (2) 21
10.5.2 System operating mode (2.1) 21
10.5.3 Control mode (2.2) 21
10.5.4 Setting of setpoints (2.3) 22
10.5.5 Forced control (2.4) + (2.4.1 to 2.4.6) 23
10.5.6 Setting of individual operating mode (2.4.1 to 2.4.6) 23
10.6 Alarm 24
10.6.1 Alarm (3) 24
10.6.2 Current alarms (3.1) 27
10.6.3 Alarm log (3.2) 27
10.7 Settings 27
10.7.1 Primary controller (4.1) 28
10.7.2 PI controller (4.1.1) 28
10.7.3 Selection of alternative setpoints (4.1.2) 28
10.7.4 Setting of alternative setpoints 2 to 7 (4.1.2.1 to 4.1.2.7) 28
10.7.5 Setpoint influence (4.1.3) 29
10.7.6 External setpoint influence (4.1.3.1) 29
10.7.7 Influence function (4.1.3.1.1) 30
10.7.8 Primary sensor (4.1.4) 30
10.7.9 Redundant primary sensor (4.1.5) 31
10.7.10 Pump cascade control (4.2) 31
10.7.11 Min. time between start/stop (4.2.1) 31
10.7.12 Max. number of starts/hour (4.2.1) 32
10.7.13 Standby pumps (4.2.3) 32
10.7.14 Forced pump changeover (4.2.4) 33
10.7.15 Test run (4.2.5) 33
10.7.16 Secondary functions (4.3) 33
10.7.17 Stop function (4.3.1) 34
10.7.18 Overview of digital inputs (4.3.7) 35
10.7.19 Functions of digital inputs (4.3.7.1 to 4.3.7.12) 35
10.7.20 Overview of analog inputs (4.3.8) 36
10.7.21 Setting of analog inputs (4.3.8.1 to 4.3.8.7) 36
10.7.22 Functions of analog inputs (4.3.8.1.1 to 4.3.8.7.1) 37
10.7.23 Overview of digital outputs (4.3.9) 37
10.7.24 Function of digital outputs (4.3.9.1 to 4.3.9.16) 37
10.7.25 Min., max. and user-defined duty (4.3.14) 38
10.7.26 Min. duty (4.3.14.1) 38
10.7.27 Max. duty (4.3.14.2) 39
10.7.28 User-defined duty (4.3.14.3) 39
10.7.29 Pump curve data (4.3.19) 39
10.7.30 Pump data (4.3.19.1) 40
10.7.31 Control source (4.3.20) 40
10.7.32 Monitoring functions (4.4) 40
10.7.33 Dry-running protection (4.4.1) 41
10.7.34 Dry-running protection with pressure/level switch (4.4.1.1) 41
10.7.35 Dry-running protection with pressure transmitter (4.4.1.2) 42
10.7.36 Dry-running protection with level transmitter (4.4.1.3) 42
10.7.37 Min. pressure (4.4.2) 43
10.7.38 Max. pressure (4.4.3) 43
10.7.39 External fault (4.4.4) 44
10.7.40 Functions, CU 351 (4.5) 44
10.7.41 Display language (4.5.1) 44
10.7.42 Display units (4.5.2) 45
10.7.43 Date and time (4.5.3) 46
10.7.44 Passwords (4.5.4) 46
10.7.45 Ethernet (4.5.5) 46
10.7.46 GENIbus number (4.5.6) 47
10.7.47 Software status (4.5.9) 47
www.motralec.com / service-commercial@motralec.com / 01.39.97.65.10