Grunbeck softliQ:SC Operating Manual Download Page 55

Page: 55 / 76

Troubleshooting

55 | 76

BA_TD

0en

_07

4_sof

tli

-S

.docx

Troubleshooting

WARNING:

Danger of contaminated drinking water due to stagnation.

● Risk of infectious diseases.

► If malfunctions do occur, have them remedied immediately.

The softliQ:SC water softener indicates malfunctions on the display. If malfunctions do occur
that cannot be remedied by the instructions given below, contact Grünbeck's technical
service/authorised service company.

► Have your system data (refer to chapter 1.7) handy.

9.1

Display messages

Acknowledge the malfunction or warning with ENTER.

Watch the display.

Compare the message displayed with the following table if the malfunction
reoccurs.

9.1.1

Warning signals (yellow symbols)

Display

Explanation

Remedy

Maintenance due!

Notify Grünbeck’s technical

service

Only displayed if
maintenance interval is
activated.

Notify Grünbeck's technical service/
authorised service company.

SC23 only:

Salt supply low!

Please refill!

Sufficient for: xy days

(order no. 127 100)

Salt supply low.

Refill salt tablets (refer to
chapter 7.8), acknowledge the
malfunction with ENTER.

Summary of Contents for softliQ:SC













































































Search results

Summary of Contents for softliQ:SC

Reviews:

Related manuals for softliQ:SC

Brands by name

Popular brands

Grunbeck softliQ:SC, Operating Manual

Search results

Summary of Contents for softliQ:SC

Reviews:

Related manuals for softliQ:SC

Brands by name

Popular brands