background image

 

 

 
 

  

 

 

C u s t o m e r   S e r v i c e   S e c t i o n

of the operation manual for

disinfection systems GENO

®

-UV 60 S

120 S
200 S

 

 

 

 
 

 

This special customer service section contains information that 
is essential for the start-up, maintenance resp. repair of the 
systems and therefore has to be carried along at all times. 
However, this additional information may only be used in 
combination with the standard operation manual. Furthermo-
re, it is only designated for the technical customer service.  

The customer service section consists of a lose collection of 
sheets that should – according to the respective chapter and 
page number (refer to header and footer) – be attached to the 
corresponding chapters of the standard operation manual.  

In order to always be well informed, it is important to keep 
the complete customer service section of the operation manual 
up to date at all times.

  

 

Edition February 2012 
Order no. 054 523 950 – inter 
-CONFIDENTIAL- 

 

Grünbeck Wasseraufbereitung GmbH

Josef-Grünbeck-Strasse 1
89420 Hoechstaedt/Danube · GERMANY
Phone +49 9074 41-0 · Fax +49 9074 41-100
www.gruenbeck.com · [email protected]

A company certified by TÜV SÜD

in accordance with DIN EN ISO 9001, DIN
EN ISO 14001, DIN EN ISO 13485 and SCC

Summary of Contents for GENO-UV 120 S

















Reviews: