![background image](http://html1.mh-extra.com/html/grone-0/gtts-15-1000/gtts-15-1000_diagnostics-and-troubleshooting-manual_2269701013.webp)
13
The results of the measurements should be identical, meaning that the flange should have the same
opening diameter and the same thickness in the entire perimeter. The admissible deviation should
not be bigger than 0.2-0.3 mm. In case of the bigger measurement deviations, make sure to replace
the clamping flange with a new one.
Solution – replace the wheel clamping with a new one.
Another factor which can cause excessive vibrations is the improper mounting of the cutting wheel.
Make sure the diameter of the mounting opening matches the spindle diameter, and that the wheel is
mounted accordingly to the indicated working direction.
Solution – mount the cutting wheel properly.
PROBLEM 2 – UNEVEN TILE CUTTING
The most common cause of uneven tile cutting is the lack of adjustment of guide bars against the blade
axis. The angle between the cutting wheel and the guide bars (limiters) should be equal to 90 degrees.
In order to align the guide bars, make sure to put an angle bar against one of the guide bars and move
the blade of the saw back and forth. If the blade maintains the same contact with the guide bar, there
is no need for regulation (Fig. B). Otherwise loosen the regulation screws (1) and the toggle (2) on both
sides of the table. It will allow for moving of the entire board with end limiters. Next, pressing constant-
ly the angle bar on the end arm, check if the blade moves straight along the meeting edge of the angle
bar on its entire length and after setting it in its proper position, preliminarily tighten the regulation
screws (1). The action shall be repeated for the other part of the blade and the position of the other arm
against the saw edge shall be regulated analogously. Next, make sure to tighten all regulation screws
and by using the toggles (2) set the limiting arms in a required position.
After the abovementioned actions have been carried out properly, both arms should create a straight
angle in a relation to the blade cutting axis.
Solution – perform an adjustment (calibration) of the front guide bars.
A detailed description can be also found in the User Manual (p. 8 and 9).
1
1
2
Fig. B – guide bar adjustment.
Summary of Contents for GTTS 15-1000
