Griesser 179086 Operating Instructions Manual Download Page 13

22 | EN 

 

 

  

EN | 23 

Status display (status LED) and its meaning 

orange 
fast 

fl

 ashing 

Channel in programming 
mode, previously 
programmed receivers 
cannot be operated. Lights 
continuously every three 
seconds in group mode 

orange, then green 

Receiver has received the 
signal sent by the hand-held 
transmitter and responded 

orange, the red 

fl

 ashing 

Receiver has not received 
the signal sent by the hand-
held transmitter 

red and green 
2 x alternately, then red 

Channel deleted in receiver 
and transmitter 

Tab. 7  Status displays and their meaning 

The transmission power and radio range are reduced as 
the battery power decreases (reduced battery capacity). 
If the status LED does not light up when a key is pressed, 
the batteries must be replaced (see Chapter 4.6, Replacing 
batteries). 

4.4.3  Group control unit and master channel (All) 

A group refers to the control of several receivers (channels) 
at the same time. The selected group is controlled 
by a travel command. 

With the Progreso 15M individual channels can be 
combined into 

fi

 ve different groups for group control. The 

master channel ("All" channel selection in the display) 
controls all available channels simultaneously. 

4.4.4  Joystick (multidirectional key) 

The joystick (4-way key) is the master control unit for 
navigating in the display menus. You can use it to select 
any of 15 channels by pressing "down" or "up". Only the 
programmed channels are displayed in the operating mode. 

individual channel (1)

individual channel (15)

group channel (1)

group channel (5)

master channel 

Fig. 3  Navigation in channels, groups, master channel 

If multiple single channels are allocated to different groups, 
the joystick can be used to select up to 

fi

 ve con

fi

 gurable 

group control units simply by moving it to the side. 

Channels are allocated to a group with the "Administration" 
menu (see menu structure in "Menu mode", Chapter 4.5). 

There is an additional channel for the master channel, 
to which all individual channels are assigned. The master 
channel is selected by moving the joystick slightly to the 
side. 

Summary of Contents for 179086

























Reviews: