background image

E30.0.0X.6C-11 

Operating Manual GRA0420VO / GRA010VO 

page 11 of 12  

8  Error codes: 

When detecting an operating state which is not permissible, the device will display an error code. 

The following error codes are defined: 

Err.1: 

Exceeding of the measuring range 

Indicates that the valid measuring range of the device has been exceeded. 

Possible causes: 

- Input signal to high 
- Sensor shorted (0(4)-20mA) 

Remedies: 

- The error-message will be reset if the input signal is within the limits. 
- check transmitter and device configuration (e.g. input signal).   

Err.2: 

Values below the measuring range 

Indicates that the values are below the valid measuring range of the device. 

Possible causes: 

- Input signal is to low or negative 
- Current below 4mA 
- Sensor broken (4-20mA) 

Remedies: 

- The error-message will be reset if the input signal is within the limits. 
- check transmitter and device configuration (e.g. input signal).   

Err.3: 

Display range has been exceeded 

Indicates that the valid display range (9999 digit) of the device has been exceeded. 

Possible causes: 

- Incorrect scale 

Remedies: 

- The error-message will be reset if the display value is below 9999. 

Err.4: 

Values below display range 

Indicates that display value is below the valid display range of the device (-1999 digit). 

Possible causes: 

- Incorrect scale 

Remedies: 

- The error-message will be reset if the display value is above -1999. 

Err.7: 

System-error 

The device features an integrated self-diagnostic-function which checks essential parts of the de-
vice permanently. When detecting a failure, error-message Err.7 will be displayed. 

Possible causes: 

- Valid operating temperature range has been exceeded or is below 
   the valid temperature range 
- Device defective 

Remedies: 

- Stay within valid temperature range 
- Exchange the defective device. 

Er.11:  Value could not be calculated 

Indicates a measuring value, needed for calculation of the display value, is faulty or out of range. 

Possible causes: 

- Incorrect scale 

Remedies: 

- Check settings and input signal 

Summary of Contents for GRA 010 VO













Reviews: