GreenTec Scorpion 330-4 S Handbook Download

Page: 73 / 95

Scorpion 4, 6 and 8

The operator must ensure that the tool is fully meshed when
the tool is lifted off the ground and before leaving the cabin.

9. The assembly is then secured with bolt, nut and split.

Remember to maintain a high level of cleanliness
in connection with hydraulics. Clean any screwed connection or

quick release couplings.

10. Mount the hoses, either by using screw joints or flat face quick release couplings,

see the section

Fejl! Henvisningskilde ikke fundet.

Always remember to lock the quick release couplings by
turning the pull ring. To avoid accidental disconnection when a

branch sweeps over the quick release coupling.

Demounting attachment tools

Demounting tools from the boom mower is done in reverse order of the mounting
procedure, see the section

Fejl! Henvisningskilde ikke fundet.

The tool is positioned on a solid surface. If possible, on a pallet so it can be moved
more easily.

No person or animal are allowed in the entire working area of the

mower if operation is carried out from the driver's cabin.

Summary of Contents for Scorpion 330-4 S
































































































Search results

Summary of Contents for Scorpion 330-4 S

Reviews:

Related manuals for Scorpion 330-4 S

Brands by name

Popular brands

GreenTec Scorpion 330-4 S, Handbook

Search results

Summary of Contents for Scorpion 330-4 S

Reviews:

Related manuals for Scorpion 330-4 S

Brands by name

Popular brands