Gree GRS-1.5/D150ANbA-K Service Manual Download

Page: 4 / 81

GREE AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

PRODUCT

1 MODELS LIST

Product type

Model

Product

Code

Heating capacity

(W)

Outline diagram

Integral type

GRS-2.4/D270ANbA-K

ER02100050

2400+1500

(electric heating)

GRS-1.5/D150ANbA-K
GRS-1.5/D200ANbA-K

ER02100070
ER02100080

1500+1500

(electric heating)

GRS-1.5/TD150ANbA-K
GRS-1.5/TD200ANbA-K

ER02100100
ER02100090

1500+1500

(electric heating)

Notes:

①

The above table lists specifications of the air source water heater series product for static heat up. The

product standard is EN16147-2011, (EU) No 814/2013, EN 12102-2008.

②

Conditions for testing heating capacity of the unit: outdoor ambient temperature: 20°C DB/15°C WB;

Initial/ending water temperature in the water tank: 15°C/55°C.

③

For units with a water tank equipped with an electrical heater, that is, the model of which includes

― D ‖,

both the heat pump and electrical heater are started for heat up under low ambient temperature or rapid

mode.

④

If the product specification changes with product improvement, refer to the parameter specified on the

nameplate.

Summary of Contents for GRS-1.5/D150ANbA-K


















































































Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands

Gree GRS-1.5/D150ANbA-K, Service Manual

Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands