Gree GRS-1.5/D150ANbA-K Service Manual Download

Page: 7 / 81

GREE AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

Model

GRS-1.5/D150ANbA-K

GRS-1.5/D200ANbA-K

Rated Heating Capacity

(*)

1500

Rated Input Power

(*)

429

COP

(*)

W/W

3.50

Capacity

150

190

Load Profile

COP

DHW

(**)

W/W

2.47

Energy Efficiency Class

(**)

Water Heating Energy Efficiency

(**)

103.9%

Annual electricity consumption

(average climate conditions)

kWh

985

Maximum Input Power

650+1500W (Electric Heater)

Outlet Water Temperature

°C

Default: 55°C, 35°C~70°C

Power Supply

220V-240V ~50Hz

Insulation Level

Ⅰ

Protection of Ingression

Ⅰ

PX4

Ⅰ

PX4

Refrigerant

Name

R134a

Charge

0.8

Outline Dimensions

591

1685

591

1935

Package Dimensions

703

1765

703

2015

Gross/Net Weight

88.0/73.5

95.5/79.0

Sound Power Level

(***)

dB(A)

Operating Range

°C

0~45

Notes:

①

(*) Value obtained with the following conditions: Outdoor temperature: 20°C DB /15°C WB; Water

tank temperature (start/end): 15°C /55°C.

②

(**) Value obtained with an air temperature of 7°C and a water inlet at 10

℃

, as per EN16147-2011,

(EU) No 814-2013.

③

(***) Value obtained indoor placement, as per EN 12102-2008, (EU) No 814-2013.

④

Under Rapid function, electric heater helps to heating water.

⑤

Please always see the nameplate for the exact data as this table is subject to change.

Summary of Contents for GRS-1.5/D150ANbA-K


















































































Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands

Gree GRS-1.5/D150ANbA-K, Service Manual

Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands