Gree GRS-1.5/D150ANbA-K Service Manual Download

Page: 48 / 81

GREE AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

COMMISSIONING and TRIAL RUN

1 Commissioning Flowchart

Check before

commissioning

Outdoor unit

Water tank

Electric connection

Start the unit for

commissioning.

Set unit parameters.

Accept after

commissioning.

2 Precautions on Safety

Before commissioning, ensure that the power supply model, possible usage range (pipe distance,

indoor and outdoor high and low voltage difference, and power supply voltage), and installation space

meet user requirements.

After verifying that no exception exists upon commissioning, introduce the operation and maintenance

method to the customer according to the user manual. In addition, deliver the precautions and user

manual to the customer for careful storage.

3 Preparations

3.1 Tool Preparation for Commissioning

Hex key

Adjustable wrench

Phillips screwdriver

Straight screwdriver

Vacuum pump

Electronic scale

High-pressure and low-pressure gauges for the related refrigerant system

Summary of Contents for GRS-1.5/D150ANbA-K


















































































Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands

Gree GRS-1.5/D150ANbA-K, Service Manual

Search results

Summary of Contents for GRS-1.5/D150ANbA-K

Reviews:

Related manuals for GRS-1.5/D150ANbA-K

Brands by name

Popular brands