background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

We reserve the right to introduce modifications. Not liable for printing errors! 

 

 

 

       01/2012 

    Made in 

Vietnam

 

16 

When assembling the rods, always take care to ensure that they move freely and can 
move  through  their  entire  controllable  path  -  including  trim  travel  -  and  are  not 
mechanically impeded. 
When the joystick moves to the right, the rudder must turn to the right (left stick/left 
rudder). When the elevator stick is moved back toward the belly, the elevators must 
deflect upward. If the stick is moved forward, the elevators must deflect downward.  If 
the aileron stick is moved to the right, the right aileron should move upward; the left 
aileron downward. When the throttle stick is pushed forward, the motor must run at 
full power; if the throttle stick and trim are moved back to their end-points, the engine 
must stop. If the trim travel is moved all the way back, the motor must stop. The 
landing flaps are best activated via a three-position switch. 
 
 
Now have fun flying your SEA Fury 1800! 
 
 

Safety tips and warnings for motorized aircraft models with internal 

combustion engines 

 
Before you first attempt to fly the model, it is essential to carefully read all the 
operating and assembly instructions. 
These safety notes are part of these instructions and must be stored carefully 
with  the  operating  instructions  and,  if  the  model  is  passed  on  to  others,  they 
must also be passed on to the next user. 
Motorised models are very demanding and dangerous objects and require that 
the user have great expertise, skill, and a sense of responsibility. 
 
Motorised models are not suitable for persons under 18 years of age. 
 
They  may  be  operated  only  under  the  instruction  and  supervision  of  an  adult 
who is familiar with the attendant hazards. 
 
The operator of the model must be in full possession of his or her bodily and 
mental  faculties.  As  with  car  driving,  operating  a  model  aircraft  under  the 
influence of alcohol or drugs is not permissible under any circumstances. 
 
Radio controlled aircraft models may be used only for the purpose intended by 
the manufacturer; meaning not as a sporting device designed to carry people. 
Any other use is forbidden. 
 
A  model  can  only  work  properly  and  fulfil  your  expectations  if  it  is  built  or 
assembled  with  the  greatest  of  care  and  in  accordance  with  the  assembly 
instructions. Independent changes in design or materials are not permitted. To 
avoid  injuring  people  and  damaging  property,  it  is  essential to  be  careful  and 
thoughtful  when  operating  your  model.  Nobody  would  climb  into  a  full-size 
glider  and  attempt  to  fly  it  without  undergoing  training  beforehand.  Model 
flying  is  also  something  that  has  to  be  learned!  We  suggest  that  you  ask  an 

Summary of Contents for SEA FURY 9354






















Reviews: