GRAUPNER SEA FURY 9354 Assembly Instructions Manual Download Page 8 | Manualshive

Page: 8 / 21

GRAUPNER SEA FURY 9354 Assembly Instructions Manual Download Page 8

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

We reserve the right to introduce modifications. Not liable for printing errors!

01/2012

Made in

Vietnam

8

The two-part landing flaps are connected using the GRP connector. As shown in the
photos, slide in the connectors and glue them into a flap.

Installation of the landing gear
As shown on the photos, install the landing gear in the wing using the four sheet
metal screws; likewise for the servos. For the attachment screws, pre-drill a pilot
hole.

The steering linkages must be adjusted so that the retractable undercarriage can be
locked in the extended and retracted positions.
Now the landing gear covers can be installed / glued on. As a test, place the covers
onto the landing gear legs, glue on with a few drops of fast setting glue, and align
them while in the retracted position. Now extend the landing gear again and glue
them onto the legs of the landing gear using Stabilit Express.

Now the wheels can be attached using the wheel axles.

«
...
6
7
8
9
10
...
»

Summary of Contents for SEA FURY 9354






















Reviews:

No comments