background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors               11/2010 

 

Radio control system 
The RC system must feature at least five control functions and ten servos. The 
transmitter should also include a servo reverse facility.

 

We particularly recommend MC-22s to MC-24 computer systems. The model is 
designed for standard-sized servos.  
We recommend the following receiver power supply: two GRAUPNER 5N-5000 
NiMH packs, Order No.98903.5, which should be maintained carefully before and 
after each flying session. Please note that batteries of this type do not reach full 
capacity until they have been charged and discharged (cycled) several times. 
 
 
 
 
 

 

 
 
 
 
You will need four suppressor filters, Order No. 1040, or a folding ferrite ring, Order 
No. 98516.1 and four extension leads, Order No. 3935.18, in order to connect the 
two aileron servos and two landing flap servos to the receiver, i.e. these leads are 
plugged into the receiver permanently. 
The following servo leads are required: one extension lead, Order No. 3935.75, for 
each aileron servo, one extension lead, Order No. 3935.32 for each landing flap 
servo, and one extension lead, Order No. 3935.75, for each elevator servo. 
The receiver and receiver batteries should be packed in soft foam for shock 
protection. 
The model is suitable for standard-sized servos with an output torque of around 50 
Ncm. 
 

Adhesives

 

Fast-setting epoxy, e.g. UHU plus schnellfest, Order No. 962 
Slow-setting epoxy, e.g. UHU plus endfest 300, Order No. 950.43 
Wood glue, e.g. UHU Holzleim express, Order No. 958.60 
UHU hart, e.g. Order No. 534.35 
Cyano-acrylate, e.g. Order No. 5821 
Cyano-acrylate, e.g. Order No. 5822 
Thread-lock fluid, e.g. Order No. 952 
 

Items required for flying the model 

(not included) 

Fuel to suit engine: petrol / oil mix (see instructions provided with the engine)  
Fuel tubing, e.g. Order No. 1325.2 
Manual fuelpump, e.g. Order No. 6870 
Ignition battery, Order No. 8716.5 
 

An appropriate battery charger and charge leads are required for the electric-
powered version of the aircraft. 

 

Summary of Contents for jodel robin dr 400/18































Reviews: