23
Check and adjust the chain tension frequently. Too loose chain can easily slide off the guide bar, quickly wear out
or quickly wear out the guide bar.
FILLING SAW TANK WITH OIL
Oil tank in new chain saw is empty. Fill the tank with oil prior to first use.
Unscrew oil filler plug (
●
18
).
Pour in maximally 260 ml of oil (be careful to avoid contamination of oil during filling of the tank).
●
Screw oil filler plug (
●
18
).
Do not use oil that has been already used or regenerated, as this may damage the oil pump.
Use SAE 10W/30 oil
for the whole year, or SAE 30W/40 in summer and SAE 20W/30 in winter.
FILLING THE FUEL TANK
When filling the fuel, follow these rules:
engine must not work,
●
you must not spill the fuel.
●
Accordingly to the below table, mix petrol (lead-free with octane number 95) with good quality engine oil for two stroke engines.
RECOMMENDED FUEL BLEND RATIO
WORKING CONDITIONS
PETROL : OIL
First 20 hours of operation
20 : 1
After 20 hours of operation
25 : 1
● Unscrew fuel filler plug (15).
Pour in previously prepared fuel blend (max. 550 ml).
●
Screw fuel filler plug (
●
15
).
Most problems with combustion engines result directly or indirectly from fuel used. You must not use oil designed
for four-stroke engines to prepare fuel blend.
OPERATION / SETTINGS
STARTING THE ENGINE
Hold the chain saw with both hands during operation.
Check level in the fuel tank and the oil tank.
●
Ensure the brake lever (
●
6
) is in the switched on position (moved to the front).
When engine is cold, pull out choke cable (
●
2
).
Set the ignition switch (
●
14
) to switched on position (
fig. C
).
Place the saw on stable ground.
●
While holding the saw pressed against ground, pull the starter line (
●
13
). First slowly so to hear the clutch gears, then
pull it strongly (
fig. D
).
After starting the saw, press the throttle lever lock (
●
1
) and throttle level (
11
) slightly (choke cable will move automatically
to switched off position).
Allow the engine to heat up with throttle lever (
●
11
) slightly pressed.
Move the brake lever (
●
6
) to switched off position (to the back).
Make a cut.
●
In case the engine does not start at the first try, pull out the choke cable (
2
) halfway and pull the starter line again.
Do not start the engine while holding the saw in hands. During start up the chain saw must rest on ground and
be held firmly.
Ensure the chain is free to move without touching any object. Do not cut any material with choke
cable pulled out.
STOPPING THE ENGINE
● Release the throttle lever (
11
) and allow the engine to run idle for a few minutes.
Set the ignition switch (
●
14
) to STOP position.
Summary of Contents for 58G945
