25
USE AND CARE INSTRUCTIONS
Never
lean over the grill cooking area while
lighting your gas grill. Keep your face and body
a safe distance (at least 18 inches) from the
Lighting Hole or Burners when lighting your grill
by match.
WARNING
!
!
Match
Lighting Stick
Troubleshooting
To purge air from your gas line and/or reset
the regulator excess gas flow device:
If the grill fails to light :
WARNING
Misalignment of Burner Tubes over Orifices
Correction:
Reposition Burner Tubes over Orifices.
Obstruction in gas line
Correction:
Remove fuel line from grill. Do not smoke!
Open gas supply for one second to clear any obstruction
from fuel line. Close off gas supply at source and recon-
nect fuel line to grill.
Plugged Orifice
Correction:
Remove Burners from grill by removing the
screw from the rear of each Burner using Phillips Head
Screwdriver. Carefully lift each Burner up and away from
gas valve Orifice. Remove the Orifice from gas valve and
gently clear any obstruction with a fine wire. Then
reinstall all Orifices, Burners, screws and cooking
components.
If an obstruction is suspected in Gas Valves or Manifold,
call the Grill Information Center
1-800-761-5456 8am to
4:30pm CST, Monday through Friday.
Obstruction in Burner Tubes
Correction:
Follow the Burner Tube cleaning procedure
on
page 32
of this Operator's Manual.
Misalignment of Ignitor on Burner
Correction:
Check for proper position of the Electrode
Tip as shown in
step 8 page 19.
The gap between the
Spark Electrode Tip and Spark Receiver should be
approximately 3/16". Adjust if necessary. With the gas
supply closed, turn any Main Burner Control Knob to
HIGH/IGN then push in and watch for the presence of a
spark at the Electrode.
Disconnected Electric Wires
Correction:
Inspect the Ignitor Junction Box found behind
the Control Panel. Connect loose Electric wires to
Junction Box and try to light the grill.
Weak AA battery
Correction:
Unscrew the Ignitor Cap and replace the
battery.
If the grill still does not light you may need to purge
air from the gas line or reset the regulator excess
gas flow device.
Note:
This procedure should be
done every time a new LP Gas tank is connected to
your grill.
Turn gas off at source and turn Control Knobs to OFF.
Wait at least 5 minutes for gas to clear, then retry.
If your grill still fails to light, check gas supply and
connec tions.
Repeat lighting procedure. If your grill still fails to
operate, turn the gas off at source, turn the Control
Knobs to OFF, then check the following:
1.
2.
3.
Turn Control Knobs to the OFF position.
Turn off the gas at the tank valve.
Disconnect regulator from LP Gas tank.
Let unit stand 5 minutes to allow air to purge.
Reconnect regulator to the LP Gas tank.
Turn tank valve on SLOWLY 1/4 of a turn.
Open the Grill Lid.
Push and turn the RIGHT Main Burner Control
Knob to HI/IGN.
Press Electric Ignitor for 3-4 seconds to light
the burners.
(Note: The Lighting Stick is placed in the drawer.)
If ignition does not occur in 5 seconds, turn the Control
Knob(s) and gas source OFF and conduct a leak test
as explained in the Use and Care section of this manual.
If no leaks are detected, wait 5 minutes for any gas
to clear and repeat the lighting procedure.
WARNING
!
!
WARNING
!
!
Should a FLASHBACK fire occur in or around
the Burner Tubes, follow the instructions below.
Failure to comply with these instructions could
result in a fire or explosion that could cause
serious bodily injury, death, or property damage.
Shut off gas supply to the gas grill.
Turn the Control Knobs to OFF position.
Open the Grill Lid.
Put out any flame with a Class B fire
extinguisher.
Once the grill has cooled down, clean
the Burner Tubes and Burners according
to the cleaning instructions in this
Operator's Manual.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Manually Lighting Your Grill By Paper Match
To light your gas grill by match, insert a match into the
Lighting Stick and follow steps 1 through 5 of the Grill
Lighting Instructions. Then, light the match and place
Lighting Stick through the Cooking Grid on the grill as
shown below. Turn the nearest Control Knob to the HI/IGN
setting to release gas. The Burner should light
immediately.
