background image

21

USE  AND  CARE  INSTRUCTIONS

CORRECT  LP  GAS  TANK  USE

LP  Gas  grill  models  are  designed  for  use  with  a  20
Ib  or  30  lb.  Liquid  Propane  Gas  (LP  Gas)  tank,  not
included  with  the  grill. 

Never 

connect  your  gas  grill  to

an  LP  Gas  tank  that  exceeds  this  capacity.  A  tank  of
approximately  12-1/4"  inches  in  diameter  by  23-3/4"
inches  high  is  the  maximum  size  LP  Gas  tank  to
use. 

You  must  use  an 

"

OPD"  gas  tank  which

offers  a  listed  Overfill

 

Prevention  Device.

  This  safety

feature  prevents  tank  from  being  overfilled  which  can
cause  malfunction  of  LP  Gas  tank,  regulator  and/or
grill.

Never 

connect  an  unregulated  LP  gas  tank  to  your

gas  grill.  The  gas  regulator  assembly  supplied  with
your  gas  grill  is  adjusted  to  have  an  outlet  pressure
of  11"  water  column  (W.C.)  for  connection  to  an  LP
gas  tank.  Only  use  the  regulator  and  hose  assembly
supplied  with  your  gas  grill. 

Replacement  regulators

and  hose  assemblies  must  be  those  specified  by
the  Manufacturer.

Have  your  LP  Gas  dealer  check  the  release  valve
after  every  filling  to  ensure  it  remains  free  of  defects.

Always  keep  LP  Gas  tank  in  upright  position.

Do  not subject  the LP Gas tank to excessive  heat.

Never  store  an  LP  Gas  tank  indoors.  If  you  store
your  gas  grill  in  the  garage 

always

  disconnect  the

LP  Gas  tank  first  and  store  it  safely  outside.

LP  Gas  tanks  must  be  stored  outdoors  in  a  well-
ventilated  area  and  out  of  the  reach  of  children.

Disconnected  LP  Gas  tanks  must  not  be  stored  in  a
building,  garage  or  any  other  enclosed  area.

The  regulator  and  hose  assembly  can  be  seen  after
opening  the  doors  (if  applicable)  and  must  be
inspected  before  each  use  of  the  grill.  If  there  is
excessive  abrasion  or  wear  or  if  the  hose  is  cut,  it
must  be  replaced  prior  to  using  the  grill  again.

Any  attempt  to  convert  the  grill  from  one  fuel  type
to  another  is  extremely  hazardous  and  must  be
performed  by  a  qualified  gas  technician  only,  using
a  NG  Conversion  Kit  purchased  from  Grand  Hall.

Never

  light  your  gas  grill  with  the  lid  closed  or

before  checking  to  ensure  the  burner  tubes  are  fully
seated  over  the  gas  valve  orifices.

The  LP  Gas  tank  must  be  constructed  and  marked
in  accordance  with  the  Specifications  for  LP-Gas
Cylinders  of  the  U.S.  Department  of  Transportation
(D.O.T.)  or  the  National  Standard  of  Canada,  CAN/
CSA-B339,  Cylinders,  Spheres  and  Tubes  for
Transportation  of  Dangerous  Goods;  and  Commis-
sion,  as  applicable.

The  LP  Gas  tank  must  have  a  shutoff  valve,
terminating  in  an  LP  Gas  supply  tank  valve  outlet,
that  is  compatible  with  a  Type  1  tank  connection
device.  The  LP  Gas  tank  must  also  have  a  safety
relief  device  that  has  a  direct  connection  with  the
vapor  space  of  the  tank.

The  tank  supply  system  must  be  arranged  for  vapor
withdrawal.

The  LP  Gas  tank  used  must  have  a  collar
to  protect  the  tank  valve.

Never

  allow  children  to  operate  your  grill.  Do

not  allow  children  or  pets  to  play  near  your  grill.
Use  of  alcohol,  prescription  or  non-prescription
drugs  can  impair  your  ability  to  properly  assemble
and  safely  operate  your  grill.
Keep  fire  extinguisher  readily  accessible.  In  the
event  of  a  oil/grease  fire,  do  not  attempt  to
extinguish  with  water.  Use  type  B  extinguisher
or  smother  with  dirt,  sand  or  baking  soda.
In  the  event  of  rain,  cover  the  grill  and  turn  off
the  burner  and  gas  supply.
Use  your  grill  on  a  level,  stable  surface  in  an
area  clear  of  combustible  materials.
Do  not  leave  grill  unattended  when  in  use.
Do  not  move  the  appliance  when  in  use.
Allow  the  grill  to  cool  before  moving  or  storing.
Do  not  use  your  grill  as  a  heater.
This  grill  is  not  intended  to  be  installed  in
or  on  recreational  vehicles  and/or  boats.
The  grill  is  not  intended  for  commercial  use.

Never 

use  charcoal  in  this  gas  grill.

!

Do  not  store  a  spare  LP-Gas  tank  under  or  near
this  appliance.
Never  fill  the  tank  beyond  80  percent  full;  and
If  the  information  in  "(a)"  and  "(b)"  is  not  followed
exactly,  a  fire  causing  death  or  serious  injury  may
occur.

A.

B.
C.

Use  your  grill  at  least  3  feet  away  from  any
wall  or  surface. 

Use  your  grill  at  least 

3  feet

away

  from  combustible  objects  that  can  melt

or  catch  fire  such  as  vinyl  or  wood  siding,
fences  and  overhangs  or  sources  of  ignition
including  pilot  lights  on  water  heaters  and  live
electrical  appliances.
Outdoor  cooking  gas  appliance  shall  not  be
used  under  overhead  combustible  construction.

Never

 use   your  gas  grill in a garage,  porch, shed,

breezeway  or  any  other  enclosed  area.

Never 

 obstruct  the flow  of ventilation  air  around

your    gas  grill    housing.
In 

windy conditions

, always position the front of

grill  to  face  oncoming  wind  to  reduce  smoke  and
heat  blowing  in  your  face  and  prevent  potential
hazards  to  self  and  grill.

!

    WARNING

!

    WARNING

!

WIND
DIRECTION

3ft.

3ft.

Summary of Contents for CGI08ALP










































Reviews: