Graco XM Series Repair Parts Download

Page: 38 / 106

Repair

313289W

Air Controls

Remove Air Control Assembly

1. Remove shroud. See

Remove Shroud

, page 30.

2. Disconnect air motor air lines and system air line.

3. Remove four nuts (7) from front of air control

bracket (301). See

XM Plural-Component

Sprayers Common Parts

on page 74.

4. Pull out assembly.

5. Follow steps in reverse order to reinstall air control

assembly.

Replace Solvent Pump Ball Valve

1. Remove shroud. See

Remove Shroud

, page 30.

2. Disconnect air motor air lines and system air line.

3. Remove four nuts (7) from front of air control

bracket (301).

4. Pull out assembly.

5. Remove two screws (329) from front of air control

bracket (301).

6. Disconnect air line (333) running to ball valve

assembly (328).

7. Replace with new ball valve assembly. See

Air

Controls Module (26C688) Parts

, page 86.

8. Follow steps in reverse order to reassemble.

Replace Solvent Air Regulator

1. Remove shroud. See

Remove Shroud

, page 30.

2. Disconnect air motor air lines and system air line.

3. Remove four nuts (7) from front of air control

bracket (301).

4. Pull out assembly.

5. Remove regulator nut (331), and disconnect air

lines (327, 333) running to regulator (322).

6. Remove regulator assembly and replace with new.

See

Air Controls Module (26C688) Parts

, page

86.

7. Follow steps in reverse order to reassemble.

Replace System Air Regulator

1. Remove shroud. See

Remove Shroud

, page 30.

2. Disconnect air motor air lines and system air line.

3. Remove four nuts (7) from front of air control

bracket (301).

4. Pull out assembly.

5. Remove regulator nut (326) and disconnect system

air line.

6. Remove the T-handle on ball valve (337).

7. Remove four nuts (320) from the back of the air

controls to remove the air control assembly.

8. Remove regulator assembly (345) from manifold

(303, 305) and replace. See

Air Controls Module

(26C688) Parts

, page 86.

9. Follow steps in reverse order to reassemble.

Replace Solenoid Inlet Air Regulator

1. Remove shroud. See

Remove Shroud

, page 30.

2. Disconnect air motor air lines and system air line.

3. Remove four nuts (7) from front of air control

bracket (301).

4. Pull out assembly.

5. Disconnect air line.

6. Remove the T-handle on ball valve (337).

7. Remove four nuts (320) from the back of the air

controls to remove the air control assembly.

8. Remove regulator assembly (309) from swivel union

(304) and replace with new. See

Air Controls

Module (26C688) Parts

, page 86.

9. Follow steps in reverse order to reassemble.

10. Set new air pressure regulator to 80-85

psi.(0.55-0.58 MPa, 5.5-5.8 bar).

Summary of Contents for XM Series











































































































Search results

Summary of Contents for XM Series

Reviews:

Related manuals for XM Series

Brands by name

Popular brands

Graco XM Series, Repair Parts

Search results

Summary of Contents for XM Series

Reviews:

Related manuals for XM Series

Brands by name

Popular brands