Graco XM Series Repair Parts Download

Page: 37 / 106

Repair

313289W

Replace Alternator Regulator

1. Remove shroud. See

Remove Shroud

, page 30

2. Disconnect main power.

3. Remove four nuts (4); leave two nuts on left side of

panel tight. Open front panel of control box (11).

4. Disconnect supply air line from alternator assembly

(265).

5. Loosen air regulator swivel fitting (276) and remove

from solenoid module (209).

6. Repair or replace alternator regulator parts as

necessary. See

Alternator Assembly

, page 84, for

repair parts. Replace air regulator swivel fitting
(276).

7. Set regulator to

18 +/- 1 psi (12.6 +/- 10 kPa, 1.26 +/-

0.07 bar).

8. Start machine. Check voltage on the alarm

information screen. Voltage should be between
10-14 volts.

277

265

209

Supply Air Line

209

276

Summary of Contents for XM Series











































































































Search results

Summary of Contents for XM Series

Reviews:

Related manuals for XM Series

Brands by name

Popular brands

Graco XM Series, Repair Parts

Search results

Summary of Contents for XM Series

Reviews:

Related manuals for XM Series

Brands by name

Popular brands