manualshive.com logo in svg

Graco XM Series, Repair Parts

Share
Download
Graco XM Series Repair Parts Download Page 34

Repair 

34

313289W

Replace Display Battery

1. Perform steps 1-4 under 

Upgrade Software

 

section, page 33.

2. Use a flat head screwdriver to pry out old battery.

3. Replace with new battery. Ensure battery fits under 

connector tabs before snapping other end in place.

NOTE:

 Use only Panasonic CR2032 batteries for 

replacement. 

4. Reassemble access cover (204e) and screws 

(204f).

Replace Display

NOTE:

 Order kit 257484 for replacement.

1. Remove shroud. See 

Remove Shroud

.

2. Disconnect power.

3. Remove four nuts (4); leave two nuts on left side of 

panel tight. Open front panel of control box (11).

4. Disconnect CAN cable from display module.

5. Remove four screws (204b) from rear display panel 

(204c) while holding front display panel (204d) in 
place.

NOTE:

 To ease removal process use clear tape to 

hold front display panel (204d) in place.

6. Remove rear display panel (204c) and disconnect 

display cable and key switch cable (239) from circuit 
board.

Do not replace battery when an explosive gas 
atmosphere may be present.

NOTICE

To avoid damaging circuit board, wear a grounding 
strap. 

Connector
Tabs

Remove Old Battery

Insert New Battery

NOTICE

To avoid damaging circuit board, wear a grounding 
strap. 

204b

204d

204c

Summary of Contents for XM Series











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands